Eclipse Remodeling & Roofing Inc.
Standing Seam Metal Roofing Specialists | Los Angeles, California
C-39 Roofing Contractor | C-43 Sheet Metal Contractor
The cost of a standing seam metal roof in Los Angeles can vary considerably depending on the size, pitch, architectural complexity, accessibility, existing roofing conditions, materials, and custom sheet-metal requirements.
The following pricing is provided by Eclipse Remodeling & Roofing Inc. as a general starting guideline only for larger residential metal roofing projects, typically 2,500–3,000 square feet or more.
Estimated Metal Roof Installation Cost
For a typical standing seam metal roofing project using 24-gauge metal, approximate starting price ranges may be:
| Roof Pitch | Approximate Price Range |
|---|---|
| 3:12 – 5:12 Pitch | $16 – $18 per sq. ft. |
| 6:12 – 7:12 Pitch | $17 – $20 per sq. ft. |
| 8:12 – 12:12 Pitch | $21 – $25+ per sq. ft. |
These ranges are intended only as a basic budgeting starting point. They are not an estimate, proposal, quotation, or guarantee of final project cost. For a broader look at pricing across roofing materials, see our 2026 roof replacement cost guide.
What Can Increase the Cost of a Metal Roof?
Roof Size
These general ranges are primarily intended for roofs approximately 2,500–3,000 square feet or larger. Smaller projects may have a higher cost per square foot because mobilization, fabrication, setup, equipment, and other fixed project costs are distributed over a smaller roof area.
Roof Design & Complexity
A simple roof is generally less expensive to install than a complex architectural roof. Skylights, dormers, valleys, hips, transitions, walls, chimneys, multiple roof sections, penetrations, and other architectural details can substantially increase labor, fabrication, material usage, and installation time.
Roof Pitch
As roof pitch increases, installation typically becomes more labor-intensive and may require additional safety equipment, staging, access equipment, and installation time.
Existing Roof Removal
Removal of an existing roofing system is not automatically included in these general square-foot ranges. Tear-off costs depend on the existing roofing material, number of layers, roof pitch, accessibility, disposal requirements, and site conditions.
Roof Deck / Plywood Condition
The condition of the existing roof deck may not be fully known until the existing roofing materials are removed. Damaged, deteriorated, inadequate, or noncompliant decking may require repair or replacement at an additional cost.
Underlayment System
Different metal roofing assemblies require different types of underlayment. Standard synthetic, high-temperature, self-adhered, fire-rated, and specialty underlayments can have substantially different material and installation costs.
Custom Sheet-Metal Accessories
Eclipse Remodeling & Roofing Inc. can fabricate custom sheet-metal components and roofing accessories, including T-tops, attic/air vents, plumbing vent flashings, penetration flashings, transitions, trim, and other custom metal details. The quantity and complexity of these components can affect the final project price.
Roof & Property Access
Limited access, steep terrain, hillside properties, restricted material staging areas, crane or lift requirements, long material-carry distances, and difficult roof access may increase labor and equipment costs.
Material Waste & Roof Complexity
Metal roofing cannot be priced accurately using roof square footage alone. Every project requires an appropriate waste and fabrication allowance. Complex roofs with numerous valleys, hips, dormers, transitions, short panel sections, and unusual architectural details generally require a higher waste percentage than simple roof designs.
Important Pricing Disclaimer
Pricing shown above reflects general market and installation conditions as of approximately September 2026 and is subject to change without notice.
Metal, underlayment, accessories, transportation, disposal, labor, equipment, and other construction costs can fluctuate. Every property and roofing system is different.
The pricing information above is provided solely as a preliminary budgeting guide and should not be interpreted as a binding estimate, contract price, guaranteed price per square foot, or representation that a particular project will fall within these ranges.
For new construction, additions, or major remodels, Eclipse Remodeling & Roofing Inc. should review the current City-approved architectural/roof plans and applicable roofing specifications before providing a project-specific proposal.
For an existing home or re-roof project, an on-site roof inspection and measurement is strongly recommended.
Final pricing can only be established after evaluating the actual project scope, roof measurements, pitch, design, access, tear-off requirements, decking condition where observable, selected roofing assembly, underlayment, metal specifications, flashing details, ventilation, custom fabrication, project logistics, and other applicable requirements.
Any additional or concealed conditions discovered during construction may require additional work and cost and should be addressed through the applicable contract/change-order process.
Eclipse Remodeling & Roofing Inc.
We specialize in standing seam metal roofing in Los Angeles, combining professional roofing installation with custom sheet-metal fabrication. Our capabilities allow us to address the complete roofing system—not simply the metal panels—including underlayment, flashings, penetrations, ventilation components, transitions, trims, and custom fabricated details.
For accurate metal roofing pricing, the best approach is not simply asking, "What is the price per square foot?"
The better question is:
"What does this particular roof require for a complete, properly detailed metal roofing system?"
That is why Eclipse Remodeling & Roofing Inc. evaluates the complete project before providing a final written proposal. Serving Pacific Palisades, Bel-Air, Malibu and the surrounding area—contact us or call (818) 497-3449 for an on-site evaluation.
This guide is for general informational and preliminary budgeting purposes only. The terms and pricing contained in an executed written contract or proposal from Eclipse Remodeling & Roofing Inc. supersede this general pricing guide.